Buyers Tie-Rod Cylinder Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Buyers Tie-Rod Cylinder. Buyers Tie-Rod Cylinder User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Quality since 1946
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • buyersproducts.com
Rebuild Instructions
Tie-Rod Cylinder Rebuild Instructions
—continued on other side
Use these instructions for the following replace-
ment parts kits:
TGC25XFCK Front Cap Replacement Kit:
Leakage around the cylinder’s rod by the rod
seals will normally indicate that the front cap
needs to be replaced.
TGC25XPRK Piston Replacement Kit:
Leakage from non-pressurized port will normally
indicate that the cylinder’s piston cup needs to
be replaced. For example… When the cylinder is
retracted, air comes out of rear cap’s port. When
cylinder is extended, air leaks out of the front
cap’s port. One or both of these conditions may
occur if the piston cup needs to be replaced.
TGC25XRCK Rear Cap Replacement Kit:
The rear cap should be replaced if the clevis
is damaged or if the port threads have been
stripped.
Cylinder Disassembly and Inspection:
1. Remove any hardware that may be assembled
to the rod’s thread. Clean off any debris that may
be on the shaft.
2. Remove the four nuts and slide out the
tie-rod screws.
3. Carefully slide the front cap over the rod
and threads.
4. Clean and inspect bushing and seals for
excessive wear. The bushing and seals are per-
manently mounted in the front cap. Replace front
cap if there is excessive wear to either of the
seals or bushing.
5. Remove the cap gaskets from both caps and
clean the gasket seats for reassembly.
6. Slide piston out of the tube. Clean and inspect
piston and tube for any excessive wear or dam-
age. Light scratch marks on the inside of the cyl-
inder will generally have no detrimental effects on
the performance of the cylinder.
Piston Replacement:
If you are assembling a cap replacement kit, skip
to step nine.
6. Hold the piston rod on the flats located near
the threads with a 1/2" wrench while loosening
the 3/8" nut holding the piston cup.
7. Remove old piston cup and assemble the new
piston cup with the urethane side facing towards
the shaft end of the rod.
8. Assemble and tighten the 3/8" nut to secure
the piston cup to the piston rod.
1 Front Cap Assembly 1 1 - -
2 Cylinder Tube 1 - - -
3 Piston Rod 1 - - -
4 Piston Cup 1 - 1 -
5 Cap Gasket 2 2 2 2
6 3/8-24 Nylock Nut 1 - - -
7 Rear Clevis Cap 1 - - 1
8 5/16-18 Tie-Rod Screw 4 - - -
9 5/16-18 Nylock Nut 4 - - -
CYLINDER COMPONENTS SERVICE PART KIT COMPONENTS
ITEM DESCRIPTION QTY. TGC25XFCK TGC25XPRK TGC25XRCK
Vue de la page 0
1 2

Résumé du contenu

Page 1 - Rebuild Instructions

Quality since 19469049 Tyler Blvd. • Mentor, Ohio 44060Phone (440) 974-8888 • Fax (440) 974-0165Toll-Free Fax 800-841-8003 • buyersproducts.comRebuild

Page 2 - Warranty Information

Quality since 19469049 Tyler Blvd. • Mentor, Ohio 44060Phone (440) 974-8888 • Fax (440) 974-0165Toll-Free Fax 800-841-8003 • buyersproducts.comQuality

Commentaires sur ces manuels

Pas de commentaire